AK-47 anatomical map, click the picture to see
After witnessing the power of the Soviet-style AK rifle, Chen Zheng and Zhao Guangming were very excited. They had created a miracle.
Chen Zheng caressed the Su-style AK rifle in his hand and looked at Su Wen."Su Wen, can you tell me about the principle behind this Soviet-style AK rifle?”
Su Wen: " Of course you can. The Soviet-style AK rifle uses the long-stroke gas-powered automatic principle. The air duct is located above the barrel. The bolt is pushed through the cylinder and the bolt is locked.”
"To put it simply, the automatic firing process of the Soviet-style AK rifle is roughly like this. First, the hammer strikes the needle, igniting the primer and the gunpowder. The gunpowder gas produced is divided into the air guide chamber at the top of the barrel through the air guide hole, pushing the cylinder backward, and the cylinder then pushing the frame backward.”
" The pistols and the frame are connected together and can sit back for a certain period of time until the gas pressure drops to a safe level. Under the effect of the unlocking helicoid on the frame, the gun body will rotate 35 degrees to the left. After unlocking the gun barrel, the frame will drive the gun body to sit back together to complete the shell extraction and shell throwing. At the same time, the spring in the magazine will lift the bullet.”
"When the bolt is moving backward, the hammer will be pressed down and the recoil spring will be compressed. When the frame and the rear end of the casing collide, the bolt assembly will stop in the backseat. Then, the bolt assembly moved forward under the action of the recoil spring. At the same time, a bullet was taken from the magazine and pushed into the chamber. Then, the bolt stopped moving.”
"After the two locking spikes of the bolt and the barrel are locked in the barrel section, the frame continues to move about 5.5mm. A single-strand recoil spring is sheathed on the recoil spring guide rod. The recoil spring guide rod is composed of two sheathed steel rods.”
Su Wen gave a simple introduction.
Regarding this knowledge, if Su Wen had not decided to max out his comprehension talent, he would not know anything about it.
The maximum level comprehension talent was really awesome.
"I see. Looks like you're not simple, Comrade Su Wen. You're really a genius!" He had managed to make such a rifle in seven days.”
"That's right. With you, I believe it will be much easier to fight the Japanese in the future."”
Chen Zheng and Zhao Tianming did not fully understand, but they did not know what was going on. They knew that this Su-style AK rifle was very powerful.
"This is just my duty.”
Zhao Tianming looked at Su Wen and said,"Little Su, Old Chen and I will report your sample gun and related information to our superiors first."”
"I believe that the leader will be very shocked when he finds out about the appearance of the Soviet-style AK rifle!”
"That's right. I hope to see the day when the Soviet-style AK rifle will be mass-produced and put into service as soon as possible!”
If he wanted to mass-produce the Soviet-style AK rifle, he would definitely need the support of the leaders and higher-ups.
Then, Zhao Tianming and Chen Zheng left excitedly.
Su Wen looked at the backs of the two of them with a worried expression.
The AK47 assault rifle in this parallel world was a version of the Soviet-style AK rifle.
But mass production was a problem.
He couldn't just let Su Wen rub his hands all the time, right?
This was unrealistic.
Mass production required the support of machine tools and equipment, as well as a large amount of steel and raw materials.
The mass-produced model of the AK-47 used a large number of stamping techniques to manufacture parts, and the technical threshold for mass production was mainly concentrated on the following parts.
First of all, the biggest obstacle was the barrel joint. It was this part that connected the barrel, receiver, and protective wood of the AK-47. A rear sight was also installed on the barrel joint.
The technical difficulty of the gun barrel was that it was a force-bearing part, so the processing process was very complicated. It had to be forged first, then processed, and finally heat treated. Many of the forming surfaces were quite complicated, so special tools had to be used.
The gun bolt and its frame were not easy to handle either. The shape of the AK-47's gun bolt was completely irregular. During processing, it was often necessary to divide the revolving forging blank into more than ten processes to form it.
The gun frame that matched the gun head was even more troublesome. The internal blind groove was curved, and it needed to be further cut and polished after the terraced strip-like straight grooves were cut on the curved surface. Not only did it take a long time, but it also required experienced and skilled workers to do it.
Other than the barrel, the gun head, and the gun frame, the stamping of the casing was also a difficult part of mass production. Firstly, there were requirements for the steel. Secondly, during processing, the casing had to be carefully clamped with a clamp to prevent the casing, which was only a few millimeters thick, from being deformed. Finally, it had to be heat treated.
In short, mass production was not an easy task.
After mass production, they still had to consider the issue of bullet production.
After all, the Soyu-style AK rifle was a repeating rifle, which consumed a lot of ammunition.
In order to ensure the power of the Soviet-style AK rifle, they definitely could not use man-made reloaded bullets or black gunpowder. Instead, they had to use smokeless gunpowder.
These were all problems that Su Wen needed to solve.
Otherwise, there would be no way to mass-produce the Soviet-style AK rifle…
I don't want to be a eunuch. Give me more data to support it. I definitely won't let you down.
I'm begging for a flower, an evaluation ticket, and a monthly ticket. Do you have 100VIP tips?
This book comes from：m.funovel.com。